Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Williamsburg Homeowners
Most chimney damage we find in Williamsburg didn’t happen overnight. A hairline crack in the crown, mortar that’s been quietly washing out behind a brownstone parapet, a flashing seam that let a little water in every storm for a few winters – these are the problems that turn a routine sweep into a rebuild if nobody catches them. Our technicians have up to 12 years of experience reading exactly this kind of damage, and we treat the chimney as a system: crown, flue, liner, flashing and firebox, not just the part that smokes. We work with professional-grade materials from names like HeatShield and DuraFlex because repairs on these buildings need to outlast the next few weather cycles. Call (855) 301-8570 to get a repair booked and a written estimate in hand.
What Our Chimney Repair Service Includes
Chimney repair covers everything from a small mortar fix to rebuilding the stack above the roofline. We handle six repair categories in Williamsburg, and each one comes with camera evidence and a written scope before we touch a single brick.
Mortar Repointing
Repointing is raking out failed mortar joints and packing in fresh mortar that actually bonds to the brick instead of sitting on top of it. You need it when joints have receded enough to leave thin gaps, or when mortar crumbles when you press it with a screwdriver. We match the mortar mix to the brick type so older Williamsburg masonry isn’t damaged by a harder mix than the brick itself.

Spalling Brick Repair
Spalling is when the face of a brick flakes, pops or peels away, and it usually starts with water getting into the masonry and freezing behind the surface. You’ll see crumbled brick faces, piles of red grit on the roof or flashing, or a chimney that looks pitted from the street. We replace the spalled units and address the moisture source that caused them, because swapping bricks without fixing the water just restarts the problem.

Chimney Waterproofing
Waterproofing is a breathable treatment applied to the masonry that repels rain while still letting moisture inside the chimney escape. You need it after any repointing or rebuild, and on any chimney with porous brick that soaks up water like a sponge. We apply it after repairs are complete, since sealing a wall that’s still actively leaking would trap the problem instead of solving it.

Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the single most common source of chimney leaks we find. You need it looked at when you see staining on ceiling joists, rust streaks down the chimney, or sealant that has cracked and pulled away. We reset or rebuild the flashing so water runs around the chimney instead of into the roofline.
Chimney Rebuilding
Rebuilding means taking down the chimney to a sound point and building it back up properly, which is the answer when the crown, upper courses and flue have all failed together. You need it when the stack leans, has large sections of missing brick, or leans away from the roofline enough that a straight-edge test shows real movement. We rebuild to a straight line, set a new crown, and finish with the right cap so the finished stack sheds water the way it should.
Tuckpointing
Tuckpointing is the finer, more precise version of repointing: recessed mortar joints with a thin raised ribbon of finishing mortar for a clean, defined look on exposed masonry. Homeowners on brownstones and older row houses ask for it when the chimney is visible from the street or a neighbor’s yard. We keep tuckpointing to the exterior cosmetic courses and never use it where a structural joint needs a full repoint.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We install and service DuraFlex flexible stainless liner systems, which come into play when a flue is cracked, oversized or otherwise unsafe to vent through, and we know where those liners flex, connect and wear over time. HeatShield ceramic resurfacing is another product we work with regularly – it’s a specialized way to restore a deteriorated flue liner from the inside rather than tearing the chimney apart, and it’s work most general handymen aren’t equipped to do. Gelco and Olympia Chimney components round out our material lineup for caps, crowns and related venting.
Repairs fail when the wrong material meets the wrong chimney. A liner sized for one flue won’t protect another, and a cap that doesn’t vent properly traps moisture instead of keeping it out. We match the product to the actual condition we find on camera, which is why we can handle the full repair without handing part of the job off. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Water stains on the ceiling or chimney breast. Brown rings or damp patches near the chimney usually trace back to failed flashing or a cracked crown, and the longer water sits in masonry the more of it has to come out. Catching it early often keeps the job at a repoint or a flashing reset instead of a rebuild.
- Crumbling mortar or brick grit on the roof. If you see sand-like piles or brick flakes below the chimney, the masonry is losing material. That’s mortar that no longer bonds, and it lets water straight into the wall cavity behind the brick.
- A white, chalky bloom on the brick. That’s efflorescence, a sign moisture is moving through the masonry and drying on the surface. It isn’t always urgent, but it’s the first visible clue that waterproofing or flashing work is due.
- A leaning or visibly cracked stack. Movement in a chimney is a structural issue and should be looked at before another freeze-thaw cycle. We check the whole stack against a straight line and look for cracks wide enough to admit water.
- Smoke that won’t draw or a smell in the room. Poor draft or a persistent smoky odor often means a damaged liner or a flue that’s no longer sealed. That’s a safety question as much as a comfort one, so it’s worth a camera look before you light another fire.
Our Chimney Repair Process – Step by Step
- 1
Inspection and camera scan. We start with a full inspection of the exterior masonry, crown, flashing and firebox, then run a camera down the flue. You see the images too, so the recommendation is based on evidence rather than a guess.
- 2
Written scope and estimate. We write out what’s wrong, what we’d do about it, and what it costs as a flat price for the job. Nothing gets added later without your say-so.
- 3
Repair day. We set up protection around the work area, make the repairs in the order that makes structural sense – crown and flashing before cosmetic finishing – and keep the site clean while we work.
- 4
Verification. After the repair we re-check the flashing seams, run a water test where it applies, and confirm the flue is clear and the draft is behaving. If something doesn’t pass, we fix it before we call the job done.
- 5
Photo report and next steps. You get a photo record of what was repaired and a straight answer on anything that can safely wait. If a liner or crown is heading toward replacement, we tell you the timeline rather than pushing it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Williamsburg?
Chimney repair in Williamsburg typically runs from about $250 for a small mortar repoint up to $6,000 or more for a full rebuild, depending on how much of the stack has to come down. Here’s how the common scenarios usually break out:
| Repair type | Typical estimated range |
|---|---|
| Mortar repointing or tuckpointing (partial) | $250 – $900 |
| Spalling brick replacement | $400 – $1,500 |
| Chimney waterproofing | $300 – $800 |
| Flashing repair or reset | $350 – $1,200 |
| Flue resurfacing (HeatShield) | $1,200 – $3,500 |
| Chimney rebuild | $3,000 – $6,000+ |
What moves the price most is height and access, how far the damage runs, and whether the repair happens at the roofline or down inside the flue. A chimney on a tall row house takes longer to work on safely than a low one, and a rebuild that has to match existing brick costs more than a straightforward repoint. The way to avoid overpaying is to insist on seeing the camera images and the written scope before you agree to anything. Our estimates are free, the price is set per job by that written estimate, and we’ll tell you plainly when a repair can safely wait a season.
Chimney Repair Near Williamsburg – Our Service Area
We serve Williamsburg and the neighborhoods around it, including Bedford-Stuyvesant, Clinton Hill, Fort Greene, Bushwick and Prospect Heights, and we also cover Crown Heights, Park Slope, Brooklyn Heights, Brownsville, East Flatbush and Flatbush. For chimney repair just across the neighborhood line we book the same way, with the same camera inspection and written estimate. Closer jobs are usually scheduled first, and we’ll give you a realistic window when you book rather than a guess. You can also read more about chimney repair in nearby Clinton Hill if that’s closer to where you are.
Serving Williamsburg, NY – Our Local Coverage Area
We serve Williamsburg and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Williamsburg
Chimney repair is fixing the structural and moisture-related parts of a chimney: mortar joints, brick faces, the crown, the flashing where it meets the roof, the flue liner and the firebox. It’s different from a sweep, which cleans soot and creosote out of a chimney that’s otherwise sound. Most repair work starts with a camera inspection so we know whether we’re dealing with a small mortar fix or something that runs deeper. Call (855) 301-8570 for an exact quote – estimates are free.
Most repairs take between half a day and two days, with a full rebuild running longer depending on height and access. A repoint or flashing reset is usually a single visit, while liner resurfacing or a rebuild gets booked as its own job with a set start date. We give you the expected timeline in the written estimate so you can plan around it.
Typical repairs in Williamsburg start around $250 for a small repoint and can reach $6,000 or more for a full rebuild. The range depends mostly on height, access and how much masonry needs to come out. The written estimate sets the final price, and there’s no surprise add-on once we start. Call (855) 301-8570 for an exact quote – estimates are free.
Yes, we install and service DuraFlex flexible liner systems and HeatShield ceramic flue resurfacing. Both are professional-grade products, and the repair is only as good as the fit to your specific flue. We also work with Gelco and Olympia Chimney components for caps and venting. Whatever brand you have, we can inspect it and tell you where it’s wearing.
Same-day repair is often possible when you call early in the day. We answer 24/7, and dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 301-8570 to check what’s available.
We stand behind the repairs we make, and the specifics are written into your estimate so you know exactly what’s covered. If something we fixed doesn’t hold, we come back and make it right. Ask about the warranty language on your scope before the work starts so there’s no question later.
Clear the floor in front of the fireplace, move anything breakable off the hearth, and make sure we can get to the roof or a safe access point. If you have pets, keep them in another room on repair day. That’s usually all we need – the rest of the setup is on us.
Schedule Your Chimney Repair Service in Williamsburg Today
A small repair today costs a fraction of the rebuild it prevents. We’ll inspect the whole system, show you the photos, and give you a flat written estimate before any work begins. Call (855) 301-8570 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. If you want the full picture first, start with a Chimney Sweep Williamsburg and we’ll flag anything that needs repair along the way.
Written by the team at Chimney Sweep Williamsburg.